MULTIQUIP FCG1-6HA Specifications Page 1

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.To find the latest revision of thispublication, visit our website at:www.multiquip.comOPERATI

PAGE 10 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)RULES FOR SAFE OPERATIONGeneral Safety ALWAYS read, understand, and follow

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 11RULES FOR SAFE OPERATIONMaintenance SafetyNEVER lubricate components or

PAGE 12 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)Intended UseOperate the FCG16HA Saw, tools and components inaccordance with

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 13NOTES

PAGE 14 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CONTROLS & COMPONENTSCOMPONENTSFigure 3. FCG16HA Concrete Saw

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 15Figures 3 shows the location of the basic controls or components,for the FCG

PAGE 16 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)Figure 4. Engine Controls and ComponentsINITIAL SERVICINGThe engine (Figure

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 17Figure 7. Pulley Alignment3. Check V-belt tension by using a tension meter (

PAGE 18 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)GUARDS, COVERS AND V-BELTSFigure 8. V-Belt Tension Check4. DO NOT over or u

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 19Failure to thoroughly inspect thediamond blade (Figure 11) foroperational sa

PAGE 2 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)PROPOSITION 65 WARNINGEngine exhaust and some ofits constituents, and some du

PAGE 20 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)1. Blade Guard - Pivot the blade guard front cover all the wayback. The gua

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 21 BLADE PLACEMENT5. Inner Flange (Collar) - This flange is fixed upon the bla

PAGE 22 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)To adjust the blade to the desired cutting depth, perform thefollowing steps

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 23Before Starting1. Read safety instructions at the beginning ofmanual.2

PAGE 24 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)OPERATION2. Place the fuel valve lever (Figure 19) to the "ON" pos

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 256. Grasp the starter grip (Figure 22) and slowly pull it out. Theresistance

PAGE 26 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)OPERATIONALWAYS keep clear of rotating or moving parts whileoperating this

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 27OPERATIONRestarting After InterventionIf cutting is interrupted where the en

PAGE 28 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)See the engine manual supplied with yourmachine for appropriateengine mainte

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 29MAINTENANCEEngine Oil ChangeDrain the used oil while the engine is warm by t

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 3Grinding/cutting/drilling of masonry, concrete, metal andother materials with

PAGE 30 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) TROUBLESHOOTING (SAW)GNITOOHSELBUORTEDALB.6ELBATMOTPMYS MELBORPELBISSOP NOI

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 31 TROUBLESHOOTING (ENGINE))ENIGNE(GNITOOHSELBUORT.7ELBATMOTPMYSESUACELBISSOPN

PAGE 32 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) TROUBLESHOOTING (ENGINE))DEUNITNOC,ENIGNE(GNITOOHSELBUORT.7ELBATMOTPMYSESUA

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 33NOTES

PAGE 34 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)EXPLANATION OF CODE IN REMARKS COLUMNThe following section explains the diff

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 35FCG16HA CONCRETE SAW 1 TO 3 UNITSWITH HONDA GX200QXC9 ENGINE1 to 3 UnitsQty.

PAGE 36 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)DECAL LOCATOR DECAL LOCATORROTATIONROTATIONDCDCBBAA“LUBRICATION”“HOT”“BELT D

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 37NO. PART NO. PART NAME QTY. REMARKS1 38231 DECAL, SLAB SAVER LARGE 12 38213

PAGE 38 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) GUARDS ASSY.GUARDS ASSY.35101112412234981716121314141515161671265

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 39 GUARDS ASSYGUARDS ASSY.NO. PART NO. PART NAME QTY. REMARKS1 25387 GUARD, BE

PAGE 4 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)TABLE OF CONTENTSSpecifications and part numbers are subject tochange withou

PAGE 40 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) GUIDES ASSY.GUIDES ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 41 GUIDES ASSY.GUIDES ASSY.NO. PART NO. PART NAME QTY. REMARKS1# 20473 SCREW,

PAGE 42 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) UNDERCARRIAGE ASSY.89456733111222UNDERCARRIAGE ASSEMBLY210131431UNDER CARRI

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 43 UNDERCARRIAGE ASSY.UNDER CARRIAGE ASSY.NO. PART NO. PART NAME QTY. REMARKS1

PAGE 44 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)HANDLE & DEPTH ADJUSTER ASSY. HANDLE & DEPTH ADJUSTER ASSY.131412153

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 45HANDLE & DEPTH ADJUSTER ASSY.NO. PART NO. PART NAME QTY. REMARKS1 25357

PAGE 46 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) ENGINE & BLADE DRIVE ASSY.ENGINE & BLADE DRIVE ASSY.141920443322181

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 47ENGINE & BLADE DRIVE ASSY.NO. PART NO. PART NAME QTY. REMARKS1 25378 ENG

PAGE 48 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)AIR CLEANER (CYCLONE) ASSY.HONDA GX200QXC9 — AIR CLEANER (CYCLONE) ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 49AIR CLEANER (CYCLONE) ASSY.NO. PART NO. PART NAME QTY. REMARKS1 16271ZE1000

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 5 SPECIFICATIONS* Nominal Mass: Mass without blade, all fluid tanks empty

PAGE 50 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CAMSHAFT ASSY.HONDA GX200QXC9 — CAMSHAFT ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 51CAMSHAFT ASSY.NO. PART NO. PART NAME QTY. REMARKS1 12209ZH8003 SEAL, VALVE S

PAGE 52 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CARBURETOR ASSY.HONDA GX200QXC9 — CARBURETOR ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 53CARBURETOR ASSY.NO. PART NO. PART NAME QTY. REMARKS1*16010ZE1812 GASKET SET

PAGE 54 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CONTROL ASSY.HONDA GX200QXC9 — CONTROL ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 55CONTROL ASSY.NO. PART NO. PART NAME QTY. REMARKS3 16500ZH8853 CONTROL ASSEMB

PAGE 56 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CRANKCASE COVER ASSY.HONDA GX200QXC9 — CRANKCASE COVER ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 57CRANKCASE COVER ASSY.NO. PART NO. PART NAME QTY. REMARKS2 11300ZE1641 COVER

PAGE 58 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CRANKSHAFT ASSY.HONDA GX200QXC9 — CRANKSHAFT ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 59CRANKSHAFT ASSY.NO. PART NO. PART NAME QTY. REMARKS2 13310ZL0600 CRANKSHAFT

PAGE 6 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)DIMENSIONSFigure 1. FCG16HA Concrete Saw DimensionsSide ViewFront Viewsnoisne

PAGE 60 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CYLINDER BARREL ASSY.HONDA GX200QXC9 — CYLINDER BARREL ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 61CYLINDER BARREL ASSY.NO. PART NO. PART NAME QTY. REMARKS1 12000ZL0810 CYLIND

PAGE 62 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)CYLINDER HEAD ASSY.HONDA GX200QXC9 — CYLINDER HEAD ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 63CYLINDER HEAD ASSY.NO. PART NO. PART NAME QTY. REMARKS1*12204ZE1306 GUIDE, V

PAGE 64 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)FAN COVER ASSY.HONDA GX200QXC9 — FAN COVER ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 65FAN COVER ASSY.NO. PART NO. PART NAME QTY. REMARKS1 19610ZL0000ZB COVER, FAN

PAGE 66 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)FLYWHEEL ASSY.HONDA GX200QXC9 — FLYWHEEL ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 67FLYWHEEL ASSY.NO. PART NO. PART NAME QTY. REMARKS1 13331357000 KEY, SPECIAL

PAGE 68 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)FUEL TANK ASSY.HONDA GX200QXC9 — FUEL TANK ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 69FUEL TANK ASSY.NO. PART NO. PART NAME QTY. REMARKS1 16854ZH8000 RUBBER, SUPP

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 7Safety precautions should be followed at all times whenoperating this equipme

PAGE 70 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)IGNITION COIL ASSY.HONDA GX200QXC9 — IGNITION COIL ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 71IGNITION COIL ASSY.NO. PART NO. PART NAME QTY. REMARKS1 30500ZE1033 COIL ASS

PAGE 72 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)MUFFLER ASSY.HONDA GX200QXC9 — MUFFLER ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 73MUFFLER ASSY.NO. PART NO. PART NAME QTY. REMARKS1 18310ZL0000 MUFFLER 12 183

PAGE 74 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)PISTON ASSY.HONDA GX200QXC9 — PISTON ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 75PISTON ASSY.NO. PART NO. PART NAME QTY. REMARKS1 13010ZL0003 RING SET, PISTO

PAGE 76 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)RECOIL STARTER ASSY.HONDA GX200QXC9 — RECOIL STARTER ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 77RECOIL STARTER ASSY.NO. PART NO. PART NAME QTY. REMARKS1 28400ZH8013ZA START

PAGE 78 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)HONDA GX200QXC9 — GASKET KIT ASSY.GASKET KIT ASSY.NO ILLUSTRATION AVAILABL

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 79GASKET KIT ASSY.NO. PART NO. PART NAME QTY. REMARKS06111ZL0000 GASKET KIT ..

PAGE 8 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) SAFETY MESSAGE ALERT SYMBOLSAccidental StartingALWAYS place the ON/OFF switc

PAGE 80 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)LABELS ASSY.HONDA GX200QXC9 — LABELS ASSY.

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 81LABELS ASSY.NO. PART NO. PART NAME QTY. REMARKS1 87521ZL0010 EMBLEM 13 87522

PAGE 82 — FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10)PAYMENT TERMSTerms of payment for parts are net 30 days.FREIGHT POLICYAll pa

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 83NOTES

OPERATION AND PARTS MANUALYour Local Dealer is:HERE’S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIALNUMBER ON-HAND WHEN CALLING© COPYRIGHT 2010, MULT

FCG16HA SAW • OPERATION AND PARTS MANUAL — REV. #1 (03/19/10) — PAGE 9RULES FOR SAFE OPERATIONThe following safety guidelines should always be used