MULTIQUIP WM70SH8C Specifications

OPERATION AND PARTS MANUALTHIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.To find the latest revision of this publication, visit our website at:

PAGE 10 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) SAFETY INFORMATIONTOWING SAFETY CAUTION  Check with your loca

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 11TOW BAR TO MIXER CONNECTIONReference Figure 1 for the installation

PAGE 12 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) SPECIFICATIONSTable 1. Mixer SpecificationsCapacity 7.0 cu. ft (198

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 13DIMENSIONSFigure 3. DimensionsCABHBC-12-INCHBALL COUPLERHPC-11-INCH

PAGE 14 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) GENERAL INFORMATIONAPPLICATIONThe MQ Whiteman WM70SH5C/WM70SH8C mi

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 15COMPONENTSFigure 4 illustrates the basic components and controls of

PAGE 16 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) INSPECTIONBEFORE STARTING1. Read all safety instructions at the b

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 17INSPECTIONFUEL CHECK1. Remove the gasoline cap located on top of f

PAGE 18 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) Figure 7. Engine ComponentsINITIAL SERVICINGThe engine (Figure

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 19PADDLE BLADE ADJUSTMENTAdjust paddles as shown in Figure 8.Figure 8

PAGE 2 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) PROPOSITION 65 WARNINGEngine exhaust and some ofits constituents, a

PAGE 20 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) START-UPThis section is intended to assist the operator with the i

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 21START-UP6. Place the belt slip lever (Figure 14) in the START/STOP

PAGE 22 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) OPERATIONMIXING/DUMPING1. The paddle shaft inside the drum should

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 23NOTES

PAGE 24 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) MAINTENANCE (ENGINE)Use Table 6 as a general maintenance guideline

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 25MAINTENANCE (ENGINE)Perform the scheduled maintenance procedures as

PAGE 26 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) MAINTENANCE (MIXER)DRUM HEAD SEALSThere is 1 set of drum hea

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 27MAINTENANCE (MIXER)Figure 26. Grease Fittings (Countershaft)WHEEL B

PAGE 28 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) INSPECT TOOTH CONTACT BETWEEN MAIN GEAR AND DRIVE PINION1. Coat 3

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 29MAINTENANCE (MIXER)Lug Nut Torque RequirementsIt is extremely im

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 3Grinding/cutting/drilling of masonry, concrete, metal andother mater

PAGE 30 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) MAINTENANCE (MIXER)SUSPENSIONThe rigid type axle and associated ha

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 31MAINTENANCE (MIXER)MIXER STORAGEFor storage of the mixer for over 3

PAGE 32 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) TROUBLESHOOTINGTroubleshooting (Engine)Symptom Possible Problem So

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 33TROUBLESHOOTINGTroubleshooting (Engine) - continuedSymptom Possible

PAGE 34 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) Mixer TroubleshootingBlades will not rotate.Worn or defective V-be

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 35WIRING DIAGRAM

PAGE 36 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) EXPLANATION OF CODE IN REMARKS COLUMNThe following section explain

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 37SUGGESTED SPARE PARTSWM70SH5C/WM70SH8C PLASTER AND MORTAR MIXER WIT

PAGE 38 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) NAMEPLATE AND DECALSINSTRUCTIONSDE SÉCURITÉ1. Lire le manuel dupro

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 39NAMEPLATE AND DECALSNO. PART NO. PART NAME QTY. REMARKS1 EM948

PAGE 4 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) TABLE OF CONTENTSWM70SH5C/WM70SH8C MixerProposition 65 Warning ...

PAGE 40 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) FRAME ASSY.MOUNT PILLOW BLOCKS FOR PINION SHAFT HEREMOUNT DRUMBEAR

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 41NO. PART NO. PART NAME QTY. REMARKS1 514842 LOCK PIN UNIT 12

PAGE 42 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) PADDLE SHAFT ASSY.TOWENDCENTERENGINE ENDENGINE ENDCENTERTOW END824

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 43PADDLE SHAFT ASSY.NO. PART NO. PART NAME QTY. REMARKS1 514752

PAGE 44 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) STEEL TUB ASSY.PART OFFRONT FRAMEPART OFREAR FRAME1445562331619688

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 45STEEL TUB ASSY.NO. PART NO. PART NAME QTY. REMARKS1 530028C D

PAGE 46 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) AXLE ASSY.108967543211198NOTES:1COMPLETE HUB ASSEMBLY INCLUDESITEM

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 47AXLE ASSY.NO. PART NO. PART NAME QTY. REMARKS1# 3469 DUST CAP

PAGE 48 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) ENGINE ASSY.857243PART OF FRAMEPART OF FRAME6152223241117272928253

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 49ENGINE ASSY.NO. PART NO. PART NAME QTY. REMARKS1 EM969013 NUT

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 5PARTS ORDERING PROCEDURESwww.multiquip.comOrdering parts has never b

PAGE 50 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) CABINET ASSY.122101112131415158816V27889565212oz

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 51CABINET ASSY.NO. PART NO. PART NAME QTY. REMARKS1 520620 CABI

PAGE 52 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) TERMS AND CONDITIONS OF SALE — PARTSPAYMENT TERMSTerms of payment

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 53NOTES

OPERATION AND PARTS MANUALYour Local Dealer is:HERE’S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIALNUMBER ON-HAND WHEN CALLINGUnited StateSMultiquip

PAGE 6 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) SAFETY INFORMATIONDo not operate or service the equipment before re

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 7SAFETY INFORMATIONGENERAL SAFETY CAUTION  NEVER operate this equip

PAGE 8 — WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) SAFETY INFORMATIONMIXER SAFETY DANGER NEVER operate the equipment

WM70SH5C/WM70SH8C MIXER • OPERATION AND PARTS MANUAL — REV. #0 (06/07/11) — PAGE 9SAFETY INFORMATIONFUEL SAFETY (GASOLINE MODELS ONLY) DANGER  DO NO